Comments on Takach Combination Press Transfer System

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:33:12 GMT

alantakach posted a comment (0:04):

There is no sound

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:27:39 GMT

alantakach posted a comment (11:09):

Credits.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:27:09 GMT

alantakach posted a comment (10:48):

Attach the stone stop to the press.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:26:38 GMT

alantakach posted a comment (10:32):

Do not use this bed hardware with the etching head installed.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:26:07 GMT

alantakach posted a comment (10:30):

Attach the bed hardware using an allen wrench.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:25:33 GMT

alantakach posted a comment (10:21):

Make sure to line up the holes.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:25:17 GMT

alantakach posted a comment (10:19):

place it onto the press with the stone stop side towards the long side of the press.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:24:39 GMT

alantakach posted a comment (10:17):

Galvanised cover and rubber

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:23:52 GMT

alantakach posted a comment (9:53):

Then place the upper cover into place and secure them both with the four screws from before.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:23:04 GMT

alantakach posted a comment (9:52):

Reatach the chainguard covers by placing the lower cover into place first.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:21:46 GMT

alantakach posted a comment (9:21):

Using a piece of wood such as a 2" x 4", create leverage on the gearbox and tighten the bolts.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:20:45 GMT

alantakach posted a comment (9:14):

Reatach the gearbox, by putting the chain on as you raise gearbox into position and retighten the bolts.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:19:51 GMT

alantakach posted a comment (9:12):

Unlock the casters, release strap, and pull the transfer table away from the printing press.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:19:08 GMT

alantakach posted a comment (9:09):

Remover the caster unit by rolliing it out from under the scraper bar housing.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:18:23 GMT

alantakach posted a comment (8:57):

make sure that the caster unit is free.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:18:03 GMT

alantakach posted a comment (8:54):

Raise the scraper bar housing.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:17:34 GMT

alantakach posted a comment (8:52):

Loosen the scraper bar lock knobs.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:16:43 GMT

alantakach posted a comment (8:26):

Using the torque wrench tighten the bolts into place.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:16:02 GMT

alantakach posted a comment (8:08):

Remove the pvc spacers and bolt the litho head into place.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:15:30 GMT

alantakach posted a comment (8:05):

Raise the scraper bar housing back up.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:13:50 GMT

alantakach posted a comment (7:51):

Once free remove the spacerrs from inside the scraper bar housing and yolk.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:12:38 GMT

alantakach posted a comment (7:52):

Lower the scraper bar housing to release the spacers.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:11:36 GMT

alantakach posted a comment (7:31):

With the help from another person move the litho head along the runners until it reaches the proper position.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:10:46 GMT

alantakach posted a comment (7:22):

Then raise the scraper bar housing to lock the specialty spacers into place.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:09:40 GMT

alantakach posted a comment (7:17):

Lower the scraper bar housing and pull the specialty spacers into place.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:08:53 GMT

alantakach posted a comment (7:10):

Place the small pvc spacers on the bolts to prevent the bolts from dragging along the press frame.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:07:35 GMT

alantakach posted a comment (6:54):

Loosen the bolts on the litho head.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:07:11 GMT

alantakach posted a comment (6:48):

Insert specialty spacers between the scraper bar housing and yolk.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:06:26 GMT

alantakach posted a comment (6:40):

Replace runners.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:06:11 GMT

alantakach posted a comment (6:36):

Insert strap, pull tight and lock into place.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:05:39 GMT

alantakach posted a comment (6:32):

lock the casters.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:00:49 GMT

alantakach posted a comment (6:13):

Remove the strap and release the casters.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 16:00:30 GMT

alantakach posted a comment (6:10):

Lift the runners up and set them on the edge of the press.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:59:13 GMT

alantakach posted a comment (5:28):

With the torque wrench tighten the bolts on both sides of the etching head.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:57:51 GMT

alantakach posted a comment (4:38):

Lower the bolts into the threaded hole on the transfer table and proceed to tighten them.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:57:10 GMT

alantakach posted a comment (4:36):

Remove the pvc pieces and set them to the side.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:56:36 GMT

alantakach posted a comment (4:27):

Raise the drum back up so that the uprights secure onto the transfer table.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:55:41 GMT

alantakach posted a comment (4:09):

Roll the etching head along the runners onto the transfer table.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:55:03 GMT

alantakach posted a comment (4:01):

With the help from another person lower the drum down so that the uprights raise up off the frame.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:53:32 GMT

alantakach posted a comment (3:35):

Raise the bolts and place the large pvc pieces under the bolts to ensure that they do not drag while moving the etching head.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:52:15 GMT

alantakach posted a comment (3:24):

The bolts freely move up and down.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:51:16 GMT

alantakach posted a comment (2:51):

Using a torque wrench loosen the bolts so that they are free to move up and down.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:49:00 GMT

alantakach posted a comment (2:41):

Lower the upper drum so that it is touching the runners.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:48:28 GMT

alantakach posted a comment (2:35):

Keeping the gearbox flush with the mounts remove the remaining two bolts and remove the gearbox.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:47:33 GMT

alantakach posted a comment (2:25):

Lower the gearbox so that the chain becomes loose enough to remove.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:46:14 GMT

alantakach posted a comment (0:47):

Using a philips head screwdriver remove the four bolts that hold the chainguard in place.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:44:40 GMT

alantakach posted a comment (1:35):

Rmeove the lower two bolts on the gearbox, then loosen the upper bolts but do not remove them completly yet.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:43:40 GMT

alantakach posted a comment (1:26):

Remove the upper chainguard first followed by the lower one.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:43:08 GMT

alantakach posted a comment (1:21):

Make sure to hold the lower chainguard so it does not fall.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:42:25 GMT

alantakach posted a comment (1:09):

The technician is supporting the chainguard with his knee.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:40:25 GMT

alantakach posted a comment (0:23):

Place the runners onto the press bed and transfer table making sure to put the roll pins into the holes.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:38:53 GMT

alantakach posted a comment (0:18):

Lock the casters on the transfer table.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:38:27 GMT

alantakach posted a comment (0:11):

Attach the strap to the transfer table.

Takach Combination Press Transfer System

alantakach — Wed, 25 Jul 2007 15:37:58 GMT

alantakach posted a comment (0:06):

Push the transfer table to the press