About This Video
This video is
This website uses Adobe® Flash™ Player 9
Download Flash Now
If you are using Internet Explorer, you will need to restart your browser
after installing Flash.
Adobe and Flash are registered trademarks of Adobe Systems incorporated.
All rights reserved.
alantakach (0:06)
2 years ago 0 + -Push the transfer table to the press
alantakach (0:11)
2 years ago 0 + -Attach the strap to the transfer table.
alantakach (0:18)
2 years ago 0 + -Lock the casters on the transfer table.
alantakach (0:23)
2 years ago 0 + -Place the runners onto the press bed and transfer table making sure to put the roll pins into the holes.
alantakach (1:09)
2 years ago 0 + -The technician is supporting the chainguard with his knee.
alantakach (1:21)
2 years ago 0 + -Make sure to hold the lower chainguard so it does not fall.
alantakach (1:26)
2 years ago 0 + -Remove the upper chainguard first followed by the lower one.
alantakach (1:35)
2 years ago 0 + -Rmeove the lower two bolts on the gearbox, then loosen the upper bolts but do not remove them completly yet.
alantakach (0:47)
2 years ago 0 + -Using a philips head screwdriver remove the four bolts that hold the chainguard in place.
alantakach (2:25)
2 years ago 0 + -Lower the gearbox so that the chain becomes loose enough to remove.
alantakach (2:35)
2 years ago 0 + -Keeping the gearbox flush with the mounts remove the remaining two bolts and remove the gearbox.
alantakach (2:41)
2 years ago 0 + -Lower the upper drum so that it is touching the runners.
alantakach (2:51)
2 years ago 0 + -Using a torque wrench loosen the bolts so that they are free to move up and down.
alantakach (3:24)
2 years ago 0 + -The bolts freely move up and down.
alantakach (3:35)
2 years ago 0 + -Raise the bolts and place the large pvc pieces under the bolts to ensure that they do not drag while moving the etching head.
alantakach (4:01)
2 years ago 0 + -With the help from another person lower the drum down so that the uprights raise up off the frame.
alantakach (4:09)
2 years ago 0 + -Roll the etching head along the runners onto the transfer table.
alantakach (4:27)
2 years ago 0 + -Raise the drum back up so that the uprights secure onto the transfer table.
alantakach (4:36)
2 years ago 0 + -Remove the pvc pieces and set them to the side.
alantakach (4:38)
2 years ago 0 + -Lower the bolts into the threaded hole on the transfer table and proceed to tighten them.
alantakach (5:28)
2 years ago 0 + -With the torque wrench tighten the bolts on both sides of the etching head.
alantakach (6:10)
2 years ago 0 + -Lift the runners up and set them on the edge of the press.
alantakach (6:13)
2 years ago 0 + -Remove the strap and release the casters.
alantakach (6:32)
2 years ago 0 + -lock the casters.
alantakach (6:36)
2 years ago 0 + -Insert strap, pull tight and lock into place.
alantakach (6:40)
2 years ago 0 + -Replace runners.
alantakach (6:48)
2 years ago 0 + -Insert specialty spacers between the scraper bar housing and yolk.
alantakach (6:54)
2 years ago 0 + -Loosen the bolts on the litho head.
alantakach (7:10)
2 years ago 0 + -Place the small pvc spacers on the bolts to prevent the bolts from dragging along the press frame.
alantakach (7:17)
2 years ago 0 + -Lower the scraper bar housing and pull the specialty spacers into place.
alantakach (7:22)
2 years ago 0 + -Then raise the scraper bar housing to lock the specialty spacers into place.
alantakach (7:31)
2 years ago 0 + -With the help from another person move the litho head along the runners until it reaches the proper position.
alantakach (7:52)
2 years ago 0 + -Lower the scraper bar housing to release the spacers.
alantakach (7:51)
2 years ago 0 + -Once free remove the spacerrs from inside the scraper bar housing and yolk.
alantakach (8:05)
2 years ago 0 + -Raise the scraper bar housing back up.
alantakach (8:08)
2 years ago 0 + -Remove the pvc spacers and bolt the litho head into place.
alantakach (8:26)
2 years ago 0 + -Using the torque wrench tighten the bolts into place.
alantakach (8:52)
2 years ago 0 + -Loosen the scraper bar lock knobs.
alantakach (8:54)
2 years ago 0 + -Raise the scraper bar housing.
alantakach (8:57)
2 years ago 0 + -make sure that the caster unit is free.
alantakach (9:09)
2 years ago 0 + -Remover the caster unit by rolliing it out from under the scraper bar housing.
alantakach (9:12)
2 years ago 0 + -Unlock the casters, release strap, and pull the transfer table away from the printing press.
alantakach (9:14)
2 years ago 0 + -Reatach the gearbox, by putting the chain on as you raise gearbox into position and retighten the bolts.
alantakach (9:21)
2 years ago 0 + -Using a piece of wood such as a 2" x 4", create leverage on the gearbox and tighten the bolts.
alantakach (9:52)
2 years ago 0 + -Reatach the chainguard covers by placing the lower cover into place first.
alantakach (9:53)
2 years ago 0 + -Then place the upper cover into place and secure them both with the four screws from before.
alantakach (10:17)
2 years ago 0 + -Galvanised cover and rubber
alantakach (10:19)
2 years ago 0 + -place it onto the press with the stone stop side towards the long side of the press.
alantakach (10:21)
2 years ago 0 + -Make sure to line up the holes.
alantakach (10:30)
2 years ago 0 + -Attach the bed hardware using an allen wrench.
alantakach (10:32)
2 years ago 0 + -Do not use this bed hardware with the etching head installed.
alantakach (10:48)
2 years ago 0 + -Attach the stone stop to the press.
alantakach (11:09)
2 years ago 0 + -Credits.
alantakach (0:04)
2 years ago 0 + -There is no sound